Each person has got his or her own theory about Installing A Bathtub.
Setting up a bathtub isn't precisely rocket science, however it does require strong plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old tub with a brand-new one is additionally a moderately tough task. If the old tub is easily obtainable, the project can relocate quickly; if you need to open a wall to get rid of the old tub as well as position the new bath tub, the task is a lot harder. In either case, the job is within a residence handyman's skills, although you will certainly need an assistant to move out the old tub and also set in the brand-new one. Make sure you have certified yourself for the task and also are comfortable trying it. As opposed to employing a specialist to take control of a halfway-completed project, it is much better to take into consideration employing one before you start. Opportunities are you may require an expert plumber to make tube connections.
This post will certainly aid you install a new tub in your shower room if you have actually currently acquired a brand-new bathtub and don't need to alter the plan of your previous water system pipes.
Your devices as well as product list need to consist of the following:
Getting ready for the Installment
Firstly, the sustaining frame supplied with the bathroom must be fitted (if called for) according to the manufacturer's instructions. Next, fit the faucets or mixer to the tub. When suitable the faucet block, it is necessary to make sure that if the faucet comes with a plastic washer, it is fitted between the bath as well as the taps. On a plastic bath, it is likewise practical to fit a supporting plate under the taps system to avoid pressure on the bath tub.
Fit the adaptable faucet adapters to the bottom of both faucets using 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bath. Make use of the nut provided by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. See to it you utilize all of the supplied washers.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom ought to now prepare to be suited its final position.
Removing Old Touches
If you require to replace old taps with brand-new ones as a part of your installment, then the first thing you should do is separate the water. After doing so, activate the taps to drain any kind of water staying in the system. The process of getting rid of the existing faucets can be quite problematic as a result of the restricted accessibility that is typically the case.
Make use of a basin wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the taps. Have a fabric ready for the continuing to be water that will come from the pipelines. Once the supply pipelines have been gotten rid of, utilize the same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from turning throughout this process. As soon as the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned of any type of old securing compound.
Prior to proceeding to fit the brand-new taps, compare the pipeline links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, after that a shank adapter is required for the brand-new taps to fit.
Mounting the Tub
Using both wooden boards under its feet, put the bathtub in the called for setting. The wood boards are useful in equally spreading the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto 4 small factors.
The next objective is to guarantee that the bath tub is leveled all round. This can be accomplished by inspecting the spirit level as well as readjusting the feet on the tub till the level checks out degree.
To install faucets, fit the bottom of the outermost adaptable tap adapter to the suitable supply pipeline by making a compression join; after that do the very same for the other faucet.
Activate the supply of water and also check all joints as well as brand-new pipework for leaks as well as tighten them if needed. Fill the tub as well as also inspect the overflow electrical outlet and the typical electrical outlet for leaks.
Lastly, deal with the bath paneling as explained in the supplier's instruction manual. Tiling as well as securing around the bath tub needs to wait until the tub has actually been used at least when as this will certainly settle it into its last placement.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will need a plastic adapter to stop damage to the thread. One end of the port fits on the plastic tail of the faucet and the other end offers a link to the current supply pipes.
If you need to fit a monobloc, then you will certainly call for reducing couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next off, place the faucet in the mounting hole in the bath/basin guaranteeing that the washing machines remain in area in between the faucet and the sink. Secure the tap in place with the maker supplied backnut. When the faucet is firmly in position, the supply pipelines can be attached to the tails of the taps. The taps can either be connected by using corrugated copper piping or with normal tap ports. The former type ought to be linked to the faucet finishes initially, tightening up just by hand. The supply pipelines can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the location where the bathroom satisfies the floor tile, it is needed to seal the joins with a silicone rubber caulking. This is important as the fitting can move enough to break a rigid seal, causing the water to penetrate the wall between the bath and also the tiling, bring about issues with moisture and feasible leakages to the ceiling listed below.
You can pick from a range of coloured sealants to blend in your fixtures and also installations. They are offered in tubes as well as cartridges, as well as are capable of sealing voids as much as a width of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with spins of soaked newspaper or soft rope. Remember to constantly load the tub with water before sealing, to permit the activity experienced when the bathtub is in use. The sealer can split relatively early if you do not take into account this activity prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise easily offered on the marketplace. It is a good idea to fit the tiles making use of water-resistant or water-proof sticky and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I hope you enjoyed our excerpt on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Many thanks for taking the time to browse our blog. Enjoyed our write up? Please share it. Let other people discover it. Thanks for taking the time to read it.
Article